US Import Tariffs from China
Applicable Tariff Rates for China-Origin Goods
The following rates apply to goods with China country of origin imported into the United States. All rates are ad valorem (percentage of customs value) unless noted.
| Tariff Type | Rate | Applies To | Status |
|---|---|---|---|
| MFN / General Rate | Varies by HTS code | All goods (baseline) | In Effect |
| Section 301 Additional Duty | 7.5% – 25% | Lists 1–4A: 7.5%–25% on most goods | In Effect |
| Section 232 (Steel/Aluminum) | 25% / 10% | 25% on steel, 10% on aluminum imports from China | In Effect |
Section 301 additional duties of 7.5%–25% apply to virtually all product categories. UFLPA rebuttable presumption applies to Xinjiang goods.
Top US Imports from China
These product categories represent the highest-volume imports from China into the United States. Each category has specific HTS codes, duty rates, and compliance requirements.
Get the Exact HTS Code + Duty Rate
Enter your product description. Our AI classifier returns the correct HTS code, applicable duty rates, and China Section 301/FTA status.
CBP Compliance for China-Origin Goods
UFLPA forced-labor screening required for Xinjiang-origin goods. Importer certifications may apply.
UFLPA & Forced Labor Compliance
Goods from China are subject to heightened CBP scrutiny under the Uyghur Forced Labor Prevention Act (UFLPA). Importers must maintain supply chain documentation proving goods were not produced with forced labor in Xinjiang. CBP may detain shipments pending review.
Country of Origin Requirements
All goods imported from China must be marked with their country of origin per CBP regulations (19 CFR 134). Goods must be "substantially transformed" in China to claim China origin — assembly alone is typically insufficient.
Section 301 additional duties of 7.5%–25% apply to virtually all product categories. UFLPA rebuttable presumption applies to Xinjiang goods.
Landed Cost from China
Get a complete cost breakdown including duty, MPF, HMF, freight, and insurance for China-origin shipments.
Compare China vs. Other Origins
See side-by-side tariff and cost comparisons for China against other major sourcing countries.
Common Questions About Importing from China
The blended average US tariff rate for imports from China is approximately 19.3% (incl. Section 301). This rate reflects a weighted average across the country's top exported product categories to the US. China-origin goods are also subject to Section 301 tariffs, which add 7.5%–25% on top of base MFN duty rates for covered products. Actual rates depend on the specific 10-digit HTS code of the imported product.
No. China does not currently have a free trade agreement with the United States. Goods from China enter at standard MFN (Most Favored Nation) rates as determined by each product's HTS code classification. The average MFN duty rate for China goods is approximately 19.3% (incl. Section 301).
Yes, China-origin goods are subject to Section 301 additional tariffs ranging from 7.5% to 25% depending on the specific product list. These surcharges stack on top of the base MFN duty rate, significantly increasing the total effective tariff for covered products. Section 232 tariffs (25% on steel, 10% on aluminum) apply to China for steel and aluminum products.
Importing from China — Complete 2026 Analysis
US–China Trade Relationship
China is the US's largest goods import source at $427B annually, but the trade relationship has become adversarial since 2018. Four rounds of Section 301 tariffs (Lists 1–4A) now cover approximately $370B of Chinese goods. The Phase One trade deal (January 2020) was never fully implemented, and the March 2026 Section 301 expansion effectively extends coverage to remaining product categories. Anti-circumvention enforcement against goods routed through third countries (Vietnam, Malaysia, Cambodia) to avoid China tariffs has intensified — CBP's Trade Remedy Law Enforcement Directorate (TRLED) conducts factory audits and origin investigations.
Practical Import Guidance for China-Origin Goods
China-origin imports face the most complex tariff stack in US trade: MFN base + Section 301 (7.5%-25%) + IEEPA 10% baseline + possible Section 232 (steel/aluminum) + AD/CVD orders on over 400 product categories. UFLPA forced labor compliance adds mandatory supply chain documentation for any product with Xinjiang-region inputs. Importers should maintain detailed bills of materials, factory audit reports, and forced labor due diligence records. Consider duty drawback for re-exported goods and FTZ strategies for manufacturing.
Key Risks and Compliance Considerations
Anti-circumvention investigations for goods assembled in Vietnam/Cambodia from Chinese components. UFLPA Xinjiang cotton rebuttable presumption. Entity List export control restrictions. CBP country of origin audits targeting electronics, textiles, and solar products.
Total Tariff Stack for China-Origin Imports
Understanding the cumulative tariff layers for China is essential for accurate landed cost calculation:
- Base MFN Rate: 19.3% (incl. Section 301) (varies by HTS code)
- Section 301 Surcharge: Lists 1–4A: 7.5%–25% on most goods — stacks on top of MFN base
- Section 232: 25% steel / 10% aluminum. 25% on steel, 10% on aluminum imports from China
- IEEPA Baseline: 10% on all non-FTA goods (April 2026 executive order)
- Merchandise Processing Fee (MPF): 0.3464% of entered value (min $31.67, max $614.35 per entry)
- Harbor Maintenance Fee (HMF): 0.125% of cargo value (ocean shipments only)
For a complete breakdown of your specific product's tariff exposure from China, order a $19 Tariff Exposure Report.
Tools for China Importers
Other US Trading Partner Tariff Profiles
Tariff rates are sourced from USITC Harmonized Tariff Schedule and Federal Register notices as of 2026-05-16. Section 301 rates reflect current USTR actions. Always verify with official sources before importing. AI-assisted analysis provided for informational purposes only — not legal or customs advice.